Compact Interlaced Dual Circularly Polarized Sequentially Rotated Dielectric-Resonator Antenna Array

Yazeed Qasaymeh

Department of Electrical Engineering,College of Engineering,Majmaah University,AL-Majmaah,11952,Saudi Arabia

Abstract: In this study, a compact 2×2 interlaced sequentially rotated dual-polarized dielectric-resonator antenna array is proposed for 5.8 GHz applications.The array is composed of a novel unit elements that are made of rectangular dielectric resonator(RDR)coupled to an eye slot for generating the orthogonal modes,and to acquire circular polarization(CP)radiation.For the purpose of miniaturization and achieving dual polarized resonance,the array is fed by two interlaced ports and each port excites two radiating elements.The first port feeds horizontal elements to obtain left hand circular polarization (LHCP).The second port feeds vertical elements to obtain right hand circular polarization (RHCP).A quarter-wave length transformer is employed to reduce the attenuation and consequently increase the array gain performance.The 35×35 mm2(0.676λ0×0.676λ0)gains were 8.4 and 8.2 dBi for port 1 and port 2, respectively, with port isolations of-33.51 dB.The design achieves a voltage standing-wave ratio (VSWR) ＜-10 dB and an axial ratio (AR) ＜- 3 dB bandwidth of 2.48% (5.766 to 5.911 GHz)for LHCP at port 1 and a VSWR ＜-10 dB and AR ＜-3 dB bandwidth of 2.28%(5.788 to 5.922 GHz)for RHCP at port 2.The findings of the proposed design validate its use for ISM band applications.

Keywords:Antenna array;compact;dielectric resonator antenna;dual polarized;interlaced;sequential rotation

1 Introduction

Dual-circularly polarized (CP)antennas have been investigated recently because of their ability to improve the channel capacity of wireless devices and enhance their spectral efficiency [1].When designing a practical dual-polarized antenna, a wide operating band, high isolation, and low crosspolarization are the major characteristics.Furthermore,antennas with low profiles are highly desired because miniaturization is the leading trend.

In meanwhile,The sequentially rotated(SR)array geometry first introduced by[2]offers several advantages,such as enhancing the circular-polarization performance,and improving the polarization purity, impedance matching, beam forming, and pattern symmetry across wider bandwidths [3,4].However,with dual-polarization architectures,ports isolation,compactness,and design simplicity are important characteristics that should be considered.

Few dual-polarized (DP)SR dielectric-resonator antenna (DRA)arrays have been re-ported in the literature.Xie et al.(2016)proposed a 2×2 array that operates at 5.94-6.54 GHz for port 1 and 5.84-6.51 GHz for port 2[5].The 80×80 mm2 array gain was 11.5 dB with ports isolation of 34 dB.Dwivedy et al.(2017)employed a Wilkinson power divider to design a 190×82 mm22×1 array,with 190×82 mm2operating on the 6-6.6-GHz band with 40-dB ports isolation [6].The peak gain was 12.5 dB.Recently, Kowalewski et al.(2020)proposed a multilayer 2×2 array to operate at 28 GHz with a peak gain of 8.49 dBi[7].

Interlacing the feeding network for an SR array will boost the DP SR array’s performance in various aspects.First, the spacing of the resonating elements can be minimized by interlacing the feeding network [8].In addition, operating with signals of different frequencies is another prime advantage that makes it compatible with multiple-input multiple-output(MIMO)systems[9].

In view of these considerations,the objectives of this study are twofold.First,a novel resonating element composed of an eye-shaped slot coupling a RDR is proposed to obtain the CP radiation.A miniaturized interlaced SR DP DRA array, operating at the IEEE 802.11 WLAN band with some gain enhancement and port isolation,is the second objective.

The manuscript is organized as follows: The geometry of the proposed single radiating element and parametric study is presented in Section 2.The interlaced SR-array layout is described in Section 3.The results and discussion are presented in Section 4.Finally,conclusions are drawn in Section 5.

2 Antenna Geometry

2.1 Single Element

A novel resonating element composed of an eye-shaped slot coupling an RDR is proposed in this section.The proposed resonating element is expected to exhibit CP radiation.In addition,the design simplicity and compactness should be considered.Fig.1 depicts an eye slot carved on the bottom plane and fed by a microstrip etched onto the opposite side.The RDR is mounted over the eye slot at the bottom plane and is omitted here to better visualize the slot fundamentals.The eye slot can be modeled using two intersecting circles of radii (r).The circle slot dimensions in Eq.(1), reported by[10,11], were used to estimate the eye-slot resonance frequency.Eq.(1)reveals that the circular-slot antenna can support the different resonance modes that are required for CP radiation.

wherexnmis themthzero of the Bassel functions andCis the speed of light.aeis the effective radius of the slot andεris the dielectric of the substrate.

The effective radius of the slot can be calculated by Eq.(2):

wherehis the substrate height.

Fig.2 depicts the 3D geometry of the proposed resonator element composed of an RDR coupled to an eye slot on the bottom plane.The RDR shape was selected because its dimensions can be chosen independently.Once the RDR is excited using a slot at the bottom plane,theTEmnmodes are excited.

The dielectric waveguide model reported in[12,13]was used to estimate the RDR resonant frequency.Eq.(3)was used to estimate the RDR dimensions at the resonance frequency.

whereεris the dielectric constant,cis the speed of light,k0is the wave number in free space,andkx,ky,andkzrepresent the wave numbers in thex,y,andzdirections inside the DR,respectively.

Figure 1:Proposed single resonator:(a)Front plane,(b)Bottom plane

Figure 2:3D geometry of the proposed resonating element

2.2 Single-Element Parametric Study

In this section, the relationship between the design sub-elements is clarified to achieve a CPmatched DRA.Fig.3 depicts the prototype single-resonating element that was modeled using the CST Microwave Studio suite simulation software.The substrate was modeled as an RO4003C substrate with a permittivity of 3.38 and a thickness of 0.813 mm.An alumina material with a dielectric constant of 10 was used to model the RDR.The parametric study was carried out on the prototype model for the optimum performance at 5.8 GHz.

Fig.4 depicts the reflection coefficient of variation in accordance with the circle radii (r)intersected to form the eye slot.The optimum resonance occurs if the radius is 5 mm with-24.58 dB at 5.795 GHz, while keeping the RDR dimensions constant at 6×6×6 mm3unchanged.It can be observed that as the radii increase,the resonant frequency decreases with more reflection-coefficient matching.Fig.5 shows the Smith chart for the optimum resonance.A small loop occurs at the loci that indicate CP radiation.In addition,a good matching of 48.62Ωcan be observed at 5.795 GHz.

Figure 3:Prototype single-element resonator used for the parametric study:(a)Microstrip on the front plane,(b)RDR mounted over the slot in the bottom plane,(c)Eye slot beneath the RDR

Figure 4:Reflection coefficients of variations with respect to the circle radii forming the eye slot

Figure 5:Simulated smith chart at the optimum resonance frequency

Fig.6 presents the AR variations in accordance to the radii alteration.A good CP purity is achieved at the optimum resonance frequency of 5.795 GHz.In addition,once the frequency increases,the resonant frequency shifts toward the left.

Figure 6:Effect of varying the slot radii on the AR

Fig.7 shows the 3D field radiation pattern of the proposed antenna.The gain was approximately 4.1 dBi with a directive radiation pattern.The simulated co-polarized electric field is higher than the cross-polarized electric field for the proposed single radiating element at an optimum resonance frequency of 5.795 GHz by 20 dB.The magnitude of the cross-polarized electric field was-17 dB.

Figure 7:3D radiation pattern of the proposed resonating element

Fig.8 depicts the excited modes of the proposed resonating element.At the optimum resonance frequency, two excited orthogonal modes are required for CP radiation at the optimum resonance frequency,namely,and.

Figure 8:Electric-field distribution for the proposed resonator

3 Array Topology

The array size can be minimized by interlacing the radiation elements.Based on this fact,the 2×2 DP SR geometry depicted in Fig.9 is proposed.The power provided by port 1 is divided into two equivalent amounts to feed the horizontal(along the x-axis)resonating elements.Similarly,the power provided by port 2 is fed to the vertical(along the y-axis)resonating elements.Hence,the polarization modes are created individually by ports 1 and 2.A quarter-wavelength transformer is employed to minimize the attenuation and consequently improve the coupled power to the slots at the bottom plane.Once designing an interlaced dual polarized array,the feeding network arms overlapping is a critical issue that should be taken into consideration while keeping a compact array size.

Fig.9a presents the impedances of the feeding networks, as a single quarter-wavelength transformer is employed.Fig.9b depicts the length of each segment.Fig.9c depicts the angle rotation at the coupling slots.The figure shows that two orthogonal signals can be manipulated at the same frequency.In[14],it was experimentally proven that the optimal element spacing for 2×2 SR arrays was 0.7λ0.Here,for the sake of miniaturization,an element spacing of 22 mm was implemented,approximately 0.425λ0at 5.8 GHz.The analysis and validation provided in[15]prove that if the element spacing is too large,the grating lobes will appear in a specific direction.Ostensibly,once the proper sequentially rotated feed networks are injected,the interlaced RHCP and LHCP sub-arrays will be well-established.In this design,the effect of overlapping the feeding networks to achieve dual-polarization operation is expected to be reduced due to the use of the coupling slots at the bottom plane.These coupling slots will isolate the radiating DRs from the feeding networks at the front plane.

Figure 9:Proposed array geometry:(a)Line impedances,(b)Lines and substrate lengths,(c)Angle at each eye slot

The current distribution over the feeding network was studied to ensure that the coupling slots were fed with sufficient power.Figs.10a and 10b depict the current distribution over the feeding network.As can be seen from the figure, a sufficient current will reach each radiating slot.Hence,sufficient power is expected to reach the coupling slots.Moreover,it can be observed that the current rotates counterclockwise.For port 1,the angles lie on the horizontal plane.Meanwhile,for port 2,the angles lie on the vertical plane.Thus, an RHCP is obtained from port 1, and an LHCP is expected from port 2.

The power allocations over the feeding array are shown in Fig.11.As can be seen from Fig.11a,the power nodes take their places exactly over the vertical coupling slots,once they are fed by port 2.In addition,the power nodes take their places just over the horizontal slot,as can be seen from Fig.10b,if they are fed by port 1.These results will maximize the radiated gain of the array.

Figure 10:Current distribution over the feed network:(a)Excited from port 1,(b)Excited from port 2

Figure 11: Power allocation over the feeding network: (a)Power distribution for port 1, (b)Power distribution for port 2

4 Results and Discussion

Fig.12 depicts the fabricated 2×2 DP S R array.The array dimensions measures 35×35 mm2.The resonating element dimensions,optimized in Section 2.2,are used to diagram the array.The RDR dimensions were 6×6×6 mm3.The two circles forming the eye-slot radii are 5.5 mm.Fig.12a depicts the dual-feeding topology on the front plane.As the RO4003C substrate was used for fabrication,the line width was 1.898 mm for 50Ωand 0.482 mm for 100Ω.The width of the quarter-wavelength transformer of 70.7Ωis 1.035 mm and its length is 7.9 mm.Fig.12b shows the eye slots in the bottom plane while omitting the RDR.Fig.12c shows the RDRs located above the slots at the bottom plane.

Fig.13 depicts the simulated and measured reflection coefficients of the proposed array.The simulated and measured results were in good agreement because of the accuracy of setting the simulation and measurement environments.For port 1,the minimal simulated resonance of-26.03 dB occurs at 5.822 GHz within a bandwidth range of 5.769-5.913 GHz.However,the measured bandwidth ranges from 5.766 to 5.911 GHz, with a minimal value of -26.78 dB at 5.816 GHz.For port 2, the bandwidth ranges from 5.788 to 5.922 GHz with a minimal resonance of-26.53 dB at 5.838 GHz for the simulation.Whereas,the minimal measured resonance of-26.28 dB occurs at 5.833 GHz within a bandwidth range of 5.788-5.919 GHz.The port isolation is shown in Fig.14.The isolation at 5.8 GHz was-33.51 dB.

Figure 12:Fabricated 2×2 SR array:(a)Front plane showing the feeding network,(b)Bottom plane showing the eye slots,(c)Bottom plane showing the drs located over the coupling slots

Figure 13:Simulated and measured reflection coefficients:(a)At port 1,(b)At port 2

Figure 14:Simulated and measured|S21|between port 1 and port 2

The simulated and measured radiated electric fields for ports 1 and 2 at 5.8 GHz are depicted in Figs.15a and 15b,respectively.Again,the simulations and measurements are in good agreement.For port 1,the co-polarized fields are higher than the cross-polarized ones;i.e.,an RHCP was achieved.For port 2,the cross-polarized fields are higher than the co-polarized ones;i.e.,an LHCP was attained.These results confirm the validity of the proposed array for acquiring dual-CP resonance by feeding the resonating elements using two ports and having proper interlaced resonating-element alignment.Figs.16a and 16b depicts the simulates and measured magnetic fields for both ports at 5.8 GHz.The magnetic field results agrees with the ones provided in Fig.15 that dual polarized resonance is achieved.Again, the agreement between the simulated and measured values were fairly good.The pattern difference between the results from both ports was minimal.

Figure 15:Radiation patterns in the xz plane:(a)Port 1,(b)Port 2

Figure 16:Radiation patterns in the yz plane:(a)Port 1,(b)Port 2

Fig.17 depicts the simulated and measured gains and ARs for both ports.The maximum measured gains obtained from port 1 and port 2 were 8.4 and 8.2 dBi, respectively, compared with the simulated ones,which were 8.58 and 8.3 dBi,respectively.The slight difference between the results obtained from the different ports may be attributed to the matching and fabrication.A notable gain enhancement was obtained with a miniaturized array structure.The measured AR＜-3 dB bandwidth was 2.48%(5.766 to 5.911 GHz)for port 1%and 2.28%(5.788 to 5.922 GHz)for port 2.In general,the simulated and measured results remained consistent.

Figure 17:Simulated and measured gains and ARs:(a)Port 1,(b)Port 2

Table 1: Comparison between the proposed array and other reported DP DRA arrays

5 Conclusion

In this study,a DP 2×2 SR DRA array has been presented.A novel resonating element composed of an eye-shaped slot coupling an RDR was proposed to obtain CP radiation.A dual interlaced port SR feeding topology was proposed to acquire dual-polarized array.The agreement between the simulated and measured data was fairly good.Tab.1 presents a comparison between the proposed method and other DP DRA arrays.A significant size reduction was observed,compared with the DP DRA arrays reported in the literature with good gain and ports isolation.For future work,the work can be further extended to enhance the array gain by increasing the number of array elements.Also,the techniques of altering the DR geometry or using copper stacked might be employed for enhancing the bandwidth performance.

Funding Statement:The author would like to thank the Deanship of Scientific Research at Majmaah University for supporting this work under Project Number R-2022-71.

Conflicts of Interest:The author declares that he has no conflicts of interest to report regarding the present study.