First principles study and comparison of vibrational and thermodynamic properties of X Bi(X=In,Ga,B,Al)

Raheleh Pilevar Shahriand Arsalan Akhtar

Department of Physics,Payame Noor University,Tehran,Iran

First principles study and comparison of vibrational and thermodynamic properties of X Bi(X=In,Ga,B,Al)

Raheleh Pilevar Shahri?and Arsalan Akhtar

Department of Physics,Payame Noor University,Tehran,Iran

In the present work,vibrational and thermodynamic properties of X Bi(X=B,Al,Ga,In)compounds are compared and investigated.The calculation is carried out using density functional theory(DFT)within the generalized gradient approximation(GGA)in a plane wave basis,with ultrasoft pseudopotentials.The lattice dynamical properties are calculated using density functional perturbation theory(DFPT)as implemented in Quantum ESPRESSO(QE)code.Thermodynamic properties involving phonon density of states(DOS)and specific heat at constant volume are investigated using quasiharmonic approximation(QHA)package within QE.The phonon dispersion diagrams for InBi,GaBi,BBi,and AlBi indicate that there is no imaginary phonon frequency in the entire Brillouin zone,which proves the dynamical stability of these materials.BBi has the highest thermal conductivity and InBi has the lowest thermal conductivity.AlBi has the largest and GaBi has the smallest reststrahlen band which somehow suggests the polar property of X Bi materials.The phonon gaps for InBi,GaBi,BBi and AlBi are about 160 cm?1,150 cm?1,300 cm?1,and 150 cm?1,respectively.For all compounds, the three acoustic modes near the gamma point have a linear behavior.CVis a function of T3at low temperatures while for higher temperatures it asymptotically tends to a constant as expected.

phonon dispersion,reststrahlen band,acoustic modes,optical modes specific heat

1.Introduction

The III–V semiconductors containing heavy bismuth(Bi) anion such as BBi,AlBi,GaBi,and InBi as well as their alloys have attracted technological interests in recent years due to applications in diode lasers,infrared photo-detectors and quadruple junction solar cells.[1–7]Most of the III–Bi compounds are expected to have a small energy gap,low ionicity, short bond length,high mechanical strength,[8–12]and high melting point.[13]Hence these materials are of great importance for numerous optoelectronic applications such as lasers, solar cells,transistors,and spintronic devices.[8,12,14–16]Bi is a key element for reduction of the band gap in GaAsBi and giant spin–orbit bowing.[5,17,18]

From experimental point of view,the III–Bi compounds are rarely studied.To our knowledge,only InBi and GaBi have been synthesized which of the latter has been incorporated in GaAs1?xBixalloys.[17,19–21]The lack of experimental data as well as their promising applications,have motivated theoretical scientists to explore structural,electronic, optical and mechanical properties of these compounds extensively during the past two decades.[8,14,16,22–24]Although considerable progress has been made in theoretical description of the structural and electronic background of these compounds and predicting new alloys,[22,25–28]many of their dynamical properties are still not well established and studies are in progress.Understanding the dynamical properties of these systems is important for characterization purposes and exploring their thermodynamic properties.Besides that,phonon dispersion diagram shows whether the structural phase is stable when no negative frequency is revealed.Hence detailed knowledge of the bulk phonon dispersion and thermodynamic properties of pure materials will be invaluable.Previous work has performed first-principles calculations of the structural and lattice-dynamical properties for the zinc-blend structure of BBi,AlBi,and GaBi while dynamical properties of InBi has not been considered.[23]

In this paper our aim is to briefly describe and compare these properties for X Bi(X=In,Ga,B,Al)compounds.First we calculate force constants for the materials which are used to compute the phonon dispersion and group velocity.Then by performing quasi-harmonic approximation,we investigate thermodynamic properties such as specific heat,entropy,free energy,and internal energy at the constant volume.

2.Methodologies

We have applied density functional theory(DFT)using the Perdew–Burke–Ernzerhof(PBE)parameterization of the generalized gradient approximation(GGA)[29]for the exchange–correlation functional and a plane-wave basis,with ultrasoft Vanderbilt pseudopotentials,[30]as implemented in Quantum ESPRESSO(QE)code.[31]The cutoff energy for the wave function and the charge density are chosen to be 40 and 400 Ry,respectively.The mesh sampling for Brillouin zone integrations is performed by 15×15×15 k-pointsmesh of Monkhorst and Pack.[32]The lattice dynamical properties are calculated using density functional perturbation theory(DFPT).[31]In particular,two dynamical matrices are calculated for 2×2×2 q-points mesh.These matrices are then Fourier interpolated to obtain the phonon dispersion curves. Thermodynamic properties involving phonon density of states (DOS)and specific heat at constant volume are investigated using quasi-harmonic approximation(QHA)package within QE.[33]

3.Results and discussion

X Bi(X=Ga,B,Al)compounds have zinc blend structure.Although InBi has a tetragonal structure experimentally,[19,20]here we studied itspropertiesin assumed zinc blend structure for comparison purpose.To check the stability of these compounds in zinc blend structure,we first studied their dynamical stability by calculating the phonon spectra.Then thermodynamic properties are calculated.For the optimization,the force tolerance is 1.0×10?3Ry/Bohr on each atom and the maximum stress closes to zero within 0.5 kbar threshold.The relaxed lattice constants are obtained as 6.4407?A,5.5166?A,and 6.4567?A for AlBi,BBi,and GaBi respectively which are in agreement with the reported results in the Ref.[23]and 6.8382?A for the zinc blend structure of InBi.

Before starting the analysis of vibrational properties for bulk X Bi(X=In,Ga,B,Al),we are going to discuss the general aspects of the phonon dispersions.Figure 1 represents the phonon dispersion diagrams for InBi,GaBi,BBi, and AlBi in high symmetry directions in Brillouin zone.The non-negative frequency of the phonon dispersions for all structures indicates that there is no imaginary phonon frequency in the entire Brillouin zone,which proves the dynamical stability of these materials.Considering two atoms in a primitive cell of these structures,there should exist six corresponding vibrational modes,in which three of them are acoustic and the others are optical modes.The interval between acoustic and optical branches where there is not any dispersion,is called phonon band gap.The gaps of InBi,GaBi,BBi,and AlBi are about 160 cm?1,150 cm?1,300 cm?1,and 150 cm?1,respectively.For all three acoustic modes near the gamma point,a linear behavior is observed for both longitudinal acoustic(LA) and transverse acoustic(TA)modes where TA mode has twofold degeneracy in X–Γ direction.Furthermore,the slope of the dispersion diagram gives the wave group velocity in the corresponding modes.The calculated TA and LA group velocities for each structure are plotted in Fig.2.

Fig.1.(color online)Phonon dispersion in high symmetric directions for(a)InBi,(b)GaBi,(c)BBi,and(d)AlBi.

From Fig.2 one can see that in Γ point,the highest group velocity corresponds to LA mode of BBi and the lowest one corresponds to TA mode of InBi structure.Acoustic region dispersion with respect to q(in mathematical words vg=dω/d q)indicates the sound speed and thermal conductivity of the material.Therefore,BBi has the highest and InBi has the lowest thermal conductivity in Γ point.However,the values of the group velocity are not generally large and therefore the materials have got low thermal conductivity.Another point worth mentioning is that the slope of dispersion diagram at the edge of the first Brillouin zone(X)is zero(see Fig.1) which leads to vg=0.Consequently,there is not any transmission or thermal conductivity at the edge of the Brillouin zone.

Fig.2.(color online)First derivative of phonon dispersion diagram (Fig.1)in Γ–X direction.

In the presence of a transverse electric field,transverse optical(TO)phonons of a polar medium couple strongly to the electric field.When the wave vectors and frequencies of the external electric field and the transverse optical phonons are in resonance with each other,a coupled phonon–photonfield is necessary to describe the system.The quantum of this coupled field is known as the polariton.We have

where ε(0)and ε(∞)are static and high frequency dielectric functions,and ωLOand ωTOare LO and TO phonon modes frequencies,respectively.In the special case ω=0 this relation reduces to the celebrated Lyddane–Sachs–Teller relationship[34]

From phonon band diagram the calculated ratio ofare 1.0325,1.0221,1.0213,and 1.0627 for InBi,GaBi,BBi, and AlBi,respectively,which are presented in Table 1.The gap between ωLOand ωTOis called reststrahlen band in which no electromagnetic wave can propagate in the medium.From Table 1,the existence of reststrahlen band for X Bi materials suggests their polar property.AlBi has the largest and GaBi has the smallest reststrahlen band.Also it is obvious that the materials exhibit optical properties for far-infrared spectrum except a narrow gap in which the wave is reflected which is called restrahlen band.

Table 1.Calculated Lyddane–Sachs–Teller relationship and reststrahlen band.

To compare the vibrational properties of these materials,we have calculated the total and projected DOS(PDOS) of phonon plotted in Fig.3.Firstly from this diagram one can find out that mentioned vibrational band gaps are consistent with phonon dispersion diagrams.Secondly it is clear that the states for acoustic modes of all structures locate between 20 cm?1to 100 cm?1except BBi which reaches up to 150 cm?1.Moreover the optical modes spread over the interval of 225–300 cm?1for AlBi,465–550 cm?1for BBi, and about 150–170 cm?1for both InBi and GaBi.The smallest atomic mass of boron with respect to Al,Ga,and In is the main factor for the far spread of the optical frequencies of BBi.Figure 4 represents phonon PDOS for X Bi(X=In, Ga,B,Al).Almost in all structures only X atoms play role in optical modes whereas both X and Bi atoms have almost equal contributions in acoustic modes phonon DOS except for higher frequencies where Bi contribution is dominant.

To conclude our discussion,thermodynamic properties of X Bi(X=In,Ga,B,Al)have been calculated via QHA within QE code.QHA is a phonon based model to describe the volume-dependent thermal effects based on the assumption that the harmonic approximation holds for every value of the lattice constant.Thermal response of the material can be understood via thermal properties,so thermodynamic calculations of X Bi(X=In,Ga,B,Al)compounds are undeniably important because it is useful for the future experiments.Thus we attempt to investigate the thermal properties of X Bi(X=In,Ga,B,Al)compounds through the quasiharmonic Debye(QHD)model.According to quantum statistical mechanics for an ensemble consisting of harmonic oscillators,Debye model describes the specific heat of solids at low temperature where the model assumes an assemblage of noninteracting quasi-particles such as phonons(lattice vibrations) which obey the Bose–Einstein statistics.In thermal equilibrium,a collection of harmonic oscillators with the angular frequency ω at temperature T has the internal energy of

where kBis Boltzmann constant.At low temperatures,one could consider three degenerate modes in every Brillouin zone point,with the frequency ofω(q,ν)=c q,where c is the sound velocity.The expression for the heat capacity,which is valid for low-temperatures would be found as

where ? and ΘD=(2π～/kB)c(3/4π?)1/3are the volume of the crystal’s unit cell and Debye temperature,respectively. As mentioned earlier to study the thermodynamic properties of X Bi(X=In,Ga,B,Al)we have applied QHA.For this purpose,non-equilibrium Helmholtz free energy(F(V,T))will be the starting point of analysis as it follows

where it has two terms,namely,the crystal’s static energy for a given volume(Esta(V))and the vibrational contributionis expressed as

where it links to the lattice vibrations via the phonon density of states g(ω).Thus solving Eq.(6),desired thermodynamic properties are obtained using the equilibrium volume V(p,T),the static energy Esta(V)and the phonon density of states g(ω).From thermodynamics we know that with the knowledge of F?,one can calculate a set of thermodynamic properties,such as the equilibrium entropy S,Helmholtz free energy F,internal energy U,and the constant-volume heat capacity CV,as

Using these equations,the curves of CVfor X Bi(X=In,Ga, B,Al)are plotted in Fig.5(a).At low temperatures,CVis a function of T3,and for higher temperatures it asymptotically tends to a constant.Finally,to study the thermal properties of matter,one has to exploit the entropy and free energy as a function of temperature.The obtained results for temperature dependence of the entropy Svib,free energy Fvib,and internal energy Eintfor X Bi(X=In,Ga,B,Al)are presented in Fig.5(b)and Fig.5(c),respectively.From Fig.5(b),wefind that the calculated entropy Svibgradually increases with increasing temperature which suggests that raising temperature causes the crystal plates to have more intense oscillations. Moreover,figure 5(c)depicts that as temperature increases the free energy Fvibgradually decreases and tends to zero and negative values while the internal energy increases.

Fig.3.(color online)Total vibrational density of states for X Bi(X=In, Ga,B,Al).

Fig.4.(color online)Projected density of states for(a)InBi,(b)GaBi,(c)BBi,and(d)AlBi.

Fig.5.(color online)(a)Specific heat,(b)entropy S vib,(c)free energy F vib and internal energy E int at constant volume for X Bi(X=In,Ga,B, Al).

4.Conclusion

In the present work based on DFT,DFPT,and QHA study, vibrational and thermodynamic properties of X Bi(X=In,Ga, B,Al)are investigated.Phonon dispersion calculations have revealed that the zinc blende phases of BBi,AlBi,GaBi,and InB compounds are dynamically stable.BBi has the highest and InBi has the lowest thermal conductivity.The largest and the smallest reststrahlen bands are for AlBi and GaBi respectively which suggests the polar property of X Bi materials.The vibrational gaps are about 160 cm?1,150 cm?1,300 cm?1, and 150 cm?1for InBi,GaBi,BBi,and AlBi,respectively. The three acoustic modes near the gamma point have got a linear behavior.At low temperatures,CVis a function of T3,and for higher temperatures it asymptotically tends to a constant value as expected.Generally,these materials exhibit appealing optical properties that can be exploited for infrared and near infrared optoelectronic applications.

[1]Ma K Y,Fang Z M,Cohen R M and Stringfellow G B 1992 J.Electron. Mater.21 143

[2]Oe K and Okamoto H 1998 Jpn J.Appl.Phys.37 L1283

[3]Oszwaldowski M Berus T,Szade J,Jozwiak K,Olejnikzak I and Konarski P 2001 Cryst.Res.Technol.36 1155

[4]Oe K 2002 Jpn.J.Appl.Phys.41 2801

[5]Francoeur S,Seong M J,Mascarenhas A,Tixier S,Adamcyk M and Tiedje T 2003 Appl.Phys.Lett.82 3874

[6]Tixier S,Adamcyk M,Tiedje T,Francoeur S,Mascarenhas A,Wei P and Schiettekatte F 2003 Appl.Phys.Lett.82 2245

[7]Vaddiraju S,Sunkara M K,Chin A H,Ning C Z,Dholakia G R and Meyyappan 2007 J.Phys.Chem.C 111 7339

[8]Wang S and Ye H 2002 Phys.Rev.B 66 235111

[9]Janotti A,Wei S H and Zhang S 2002 Phys.Rev.B 65 115203

[10]Knittle E,Wentzcovitch R M,Jeanloz R and Cohen M L 1989 Nature 337 349

[11]Garcia A and Cohen M L 1993 Phys.Rev.B 47 4215

[12]Wentzcovitch R M,Cohen M L and Lam P K 1987 Phys.Rev.B 36 6058

[13]Wettling W and Windscheif J 1984 Solid State Commun.50 33

[14]Zhang Y,Mascarenhas A and Wang L W 2005 Phys.Rev.B 71 155201

[15]Madouri D and Ferhat M 2005 Phys.Status Solidi B 242 285

[16]Ferhat M and Zaoui A 2006 Phys.Rev.B 73 115107

[17]Fluegel B,Francoeur S,Mascarenhas A,Tixier S,Young E C and Tiedje T 2006 Phys.Rev.Lett.97 067205

[18]Madouri D,Boukra A,Zaoui A and Ferhat M 2008 Comp.Mater.Sci. 43 818

[19]Jorgensen J D and Clark J B 1980 Phys.Rev.B 22 6149

[20]Degtyareva V F,Winzenick M and Holzapfel W B 1998 Phys.Rev.B 57 4975

[21]Francoeur S,Seong M J,Mascarenhas A,Tixier S,Adamcyk M and Tiedje T 2003 Appl.Phys.Lett.82 3874

[22]Amrani B,Achour H,Louhibi S,Tebboune A and Sekkal N 2008 Solid State Commun.148 59

[23]Belabbes A,Zaoui A and Ferhat M 2008 J.Phys.-Condens.Mat.20 415221

[24]Rahim N A A,Ahmed R,Haq B U,Mohamad M,Shaari A,Ali N and Goumri-Said S 2016 Comp.Mater.Sci.114 40

[25]Cang Y P,Lian S B,Yang H M and Chen D 2016 Chin.Phys.Lett.33 066301

[26]Wu J H and Liu C X 2016 Chin.Phys.Lett.33 036202

[27]Feng S Q Li J Y and Cheng X L 2015 Chin.Phys.Lett.32 036301

[28]Wang J F,Fu X N,Zhang X D,Wang J T,Li X D and Jiang Z Y 2016 Chin.Phys.B 25 086302

[29]Hohenberg P and Kohn W 1964 Phys.Rev.B 136 864

[30]Vanderbilt D 1985 Phys.Rev.B 32 8412

[31]Baroni S,de Gironcoli S,Dal Corso A and Giannozzi P 2001 Rev.Mod. Phys.73 515

[32]Monkhorst H J and Park J D 1976 Phys.Rev.B 13 5188

[33]Baroni S 2011 EPJ Web of Conferences 14 02001

[34]Lyddane R H,Sachs R G and Teller E 1941 Phys.Rev.59 673

22 January 2017;revised manuscript

4 June 2017;published online 31 July 2017)

10.1088/1674-1056/26/9/093107

?Corresponding author.E-mail:ra pilevar@yahoo.com

?2017 Chinese Physical Society and IOP Publishing Ltd http://iopscience.iop.org/cpb http://cpb.iphy.ac.cn